Caring for remote control helicopters can be easy to do. Keeping them in proper working order also requires certain duties that can seem intimidating at first glance. Luckily, many of the steps are easy enough that even kids can participate in their upkeep! Read on to find out how to make sure your RC helicopter is ready to fly on the day you need it.
Let’s be with Dream Cheeky to find out how to charge remote control helicopter with these easy maintenance tips!
How To Charge Remote Control Helicopter
You are probably here because you have lost your manual. Now you need to learn how to charge your remote-controlled helicopter. While some might believe it’s as easy as plugging the device in and turning it on, most people ignore the warning labels in the manual or pamphlet and cause injury or damage to their helicopters.
How can you charge your RC helicopter via USB? There are three ways to charge your RC helicopter. It can be charged via the remote, the computer, or a regular outlet. It is not a good idea to use any other USB charger, as the one that comes with it is specifically designed for this model.
Although it is easy to find power for electronics nowadays, people often fail to understand that the warnings in bold are there for your safety and protection. Anybody who does not follow the instructions could endanger themselves or others in their vicinity.
Determination Of The Battery Type
This is the first task to determine which battery type is used for remote control helicopter operation. There are many types of batteries that can be used to operate remote control helicopters. Different cells may be used to power the remote control helicopter. Some remote control helicopter batteries allow you to disconnect the battery from its body to charge. We need to verify that. Once we have identified the type of battery, the charger must be chosen according to it.
Charging Using USB
Before plugging in, make sure that the power switch is set to “off”. No matter what power source you choose, plug the cord into the remote control helicopter first. After plugging in the other end, the light will turn on to indicate that the remote control helicopter is charging.
An AC adapter is required to plug the remote control helicopter into the wall. The indicator light will go off when the helicopter has fully charged. It takes approximately 50-60 minutes to charge the remote control helicopter. The charging time and the flying time are dependent on the model, brand, and size. They can all last approximately the same amount of time.
Keep in mind, however, that you may need to change the batteries in your controller if you plan to use it to charge the remote control helicopter. These batteries are not rechargeable.
Remote controller helicopters can be charged using a USB connection. The kit will include a charger to fully charge your transmitter or controller. In this case, your transmitter or the controller needs to be fully charged with the help of a charger which will be provided with the kit. This charging system has the advantage of being able to charge remote control helicopters anywhere you want, provided that the charger is fully charged.
What Are The Precautions And Safety Required While Charging A Remote-control Helicopter?
We need to make sure that the switch of the alternating current source is switched off while plugging in.
You must ensure that the remote control helicopter is always under adult supervision.
It is important to keep the cord and the charger away from any water source.
To charge your Remote-control helicopter, you should not use any universal USB. Only the cable that comes with it is acceptable. Universal chargers aren’t the right type of charger that a Remote Control helicopter can use safely.
You can avoid damage to the circuits or the outside design by charging it on a flat surface. It is less likely that it will fall.
If you want to replace the battery, do not touch it.
The batteries can be flammable so ensure they are not overheated as they could explode, causing damage to your remote control helicopter and injuring others.
To avoid overheating, wait until your batteries cool down after flying before plugging them in.
Unhandled Charging
A universal charger should not be used. This is because a phone power cable isn’t really a charger. The actual charger is in the phone. The cord is simply a 5V connector for power.
The 100mAh lithium polymer battery is required for most RC helicopters. To charge, it requires a current of 0.1A and a voltage of 4.2V. A power cord that is too powerful can heat up your battery and cause it to catch fire or explode.
The lithium-ion liquid is a reactive chemical that can catch fire and explode. It is safer than a lipo battery, but not as efficient. Avoiding overcharging your RC batteries will prevent you from damaging them and help you avoid a battery explosion and a fire.
Troubleshooting
There are always problems that can arise. You will want to fix them as soon as you can. These are just a few of the possible problems that could arise, along with simple solutions you can use.
1. Not holding a charge
It is possible that the voltage is incorrect. You can check the voltage using a multimeter. It should not exceed or fall below the voltage that your Remote control helicopter is designed to handle. You can try charging it again if it isn’t at the right voltage. This can be a problem if your battery is not the same size as before.
If the problem persists, you may need to replace the batteries. It could also be that your batteries are charging too high. It is important to turn off the charger when it is charging. It is important to take it out of the charger immediately after it has fully charged.
Too much liquid exposure. It is best to keep it away from the sink and other high-splash areas. You should also know how many hours you have left on your battery if you fly your helicopter close to water. It is not a good idea to hover your remote control helicopter above a stream or lake and let it fall in the water.
2. Slow Response Time
If you are around other RC helicopters, your controller could be on the same frequency as theirs, which confuses your remote control helicopter. Fly elsewhere, or change the frequency.
Your remote control’s battery could be almost dead, which could cause slow response times. Remotes typically have 9v batteries so it is worth checking if the response time is slow.
3. Not Working
It is possible that your RC helicopter is not moving or functioning properly. Either a power problem or an electronic problem is the cause. It could be that an electronic component has been damaged or loosening after an RC helicopter was dropped or crashed. It’s a good idea for you to take apart your helicopter and inspect the wiring and other components for any damage.
Power issues are usually caused by a problem with the battery on your RC helicopter, but it could also be a problem with the controller’s battery. It is possible to replace most batteries fairly inexpensively, so replacing both batteries should be an easy first step. This can be used to upgrade the battery in your RC helicopter, but you should not exceed the manufacturer’s recommended sizes.
Battery Replacement
If you have not been able to resolve any problems, it may be time to purchase a new battery. Although lipo batteries can be expensive or inexpensive depending on their quality, you’ll want one that is comparable to your old one.
This is crucial. This is the same as choosing a charger based on its specifications. The batteries will be the same. These are the factors you need to consider when buying a new battery to avoid complications and injuries to the chopper as well as to yourself.
The voltage is the number printed on the package. This number is the minimum voltage. Your Remote control helicopter will be damaged if it is too high or too low.
The capacity A larger remote control helicopter will require a different power source than a smaller one. The battery’s capacity will determine how long the helicopter can stay in the air.
The weight. Whatever the weight of the old batteries was, it will be the exact weight that you want for your new batteries. This is because you want the chopper’s performance to continue to be as good as or better than ever before.
Flight time – Be sure to check if the new battery will give you the same or longer flight time as the one you have.
Conclusion
We just provided for you the needed information related to charging an RC copter battery. Based on this information, you are good to go! We hope you find it helpful in this article.
